Refractory Coatings

• The composition of "Armor-Fire protection" is subject to tinting, while the fire resistance of the coating does not deteriorate; An advantageous solution for performing fire-retardant tasks;
• Reduction of labor costs and cost of work;
• The coating (without an additional protective layer) is intended for indoor  use for 30 years;
• The quality of the composition "Armor-Fire Protection" allows you to do what until recently was considered impossible: to protect light metal structures to the degree of R120. The composition was specially developed for use at sports and infrastructure facilities, where with a large area of buildings, the load on the enclosing structures is low, and the given thicknesses of the bearing metal are small. At the same time, the traditional advantages of "Armor-Fire Protection" are fully preserved - low costs, ease of application and long service life of the coating.

The fire protection tasks for each object are different. Our specialists help to choose the optimal solution for each object.

Recommendations on the choice of a

protective system, development of special technical conditions, expert approvals,

calculation. Specialists of the engineering and technical department advise both on the design solutions of the fire safety section and on the preparation and execution of work - and in some cases our consultations have allowed the customer to significantly reduce the cost of fire protection.

The principle of operation of Armor-Fire protection

When heated, vapors and inert gases are released, which do not support and slow

down gorenje, a protective substitution of oxygen with gases and vapors is formed.

Thus, flame-retardant paints not only block thermal convection at the protected surface, but also significantly reduce and suppress the flame. At the same time, the upper layer of the protected surface thickens, coxes and acquires the necessary rigidity. The paint contains flame retardants, specialized gas-forming agents, foam layer stabilizers and heat-resistant substances based on a polymer binder.

Scope of application

• Metal structures of the infrastructure of oil refineries (refineries);
• Objects of chemical enterprises, including those that are a source of
• exposure to weakly and moderately aggressive acid or alkaline media;
• Open and closed parking lots, bookcases, overpasses;
• Civil engineering facilities without any restrictions;
• Other objects where it is advisable to use flame-retardant paints without finishing coatings.
  

The Facade armor is a weather-resistant, high-viscosity composition specially designed for thermal insulation of vertical surfaces. The coating applied to the wall from the inside or outside forms a single seamless surface, retains heat throughout the entire volume of the room, which has a positive effect on the microclimate.

The Armor Facade coating reflects up to 80% of the visible solar and infrared radiation spectrum. This leads to a significant reduction in the heating of the interior in the summer, the cost of air conditioning, and in the cold season – can reduce heat loss by up to 30%.

The thermal insulation coating Armor Facade is a durable material with high adhesion to any building materials, along with good vapor permeability, it has hydrophobic (water–repellent) properties.

  Liquid ceramic thermal insulator Armor Facade is used for thermal insulation of plastered, concrete, brick, wooden and other surfaces of enclosing structures of buildings and structures during exterior and interior work. Ceramic heat insulator Armor Facade can be covered on top with acrylic paint on a water dispersion basis, wallpapering is allowed. Tinting of the Armor Facade is allowed only under the condition of strict compliance with our technical map, following our recommendations on the selection of tinting pastes, technical nuances.

The use of the Armor Facade coating allows:



• perform thermal insulation of walls both outside and inside;
• to preserve the volume of usable area (with thermal insulation of the walls from the inside);
• do not increase the load on the building structure;
• isolate facades with complex architectural solutions (including during reconstruction works);
• increase the temperature comfort of the room;
• reduce costs and time for construction work.

Thermal insulation paint Armor Facade also showed itself perfectly together with the modification of Armor Antikor. For example, the estimated thickness of ultrathin thermal insulation on a ferrous metal tank is 2.5 mm.

Our solution is only three layers (!):

1. 0.5 mm Antikor armor (Not only corrosion fixation, but also converter, adhesive and waterproofing (due to the high film formation rate).
2. after 24 hours - 1 mm Armor Facade
3. after 24 hours - 1 mm Armor Facade
   

Ultrathin thermal insulation Armor Classic is highly effective in the thermal insulation of building facades, roofs, interior walls, window slopes, concrete floors, hot and cold water pipelines, steam pipelines, air ducts for air conditioning systems, cooling systems, various tanks, tanks, trailers, refrigerators, etc.

It is used to eliminate condensation on cold water pipes and reduce heat loss according to the SNiP in heating systems.

The material is operated at temperatures from -60 ° C to +200 ° C (up to +260 ° C in peak short-term mode).

The service life of the material is from 15 years. To date, our material is used at facilities and enterprises of various fields of activity.

Liquid ultrathin Thermal insulator Armor Classic is the best ultrathin thermal

insulator today that you have seen, used, applied! Thanks to the modern in-house

laboratory, the ability to quickly use the novelties of the world leaders of the

chemical industry in order to improve and optimize, the vast experience in the

development and introduction of ultra-thin coatings into industrial production, the

liquid thermal insulator Armor Classic has not surpassed thermal physics, plasticity and lightness.

A plastic euro bucket of 20 liters of thermal insulation paint Armor Classic weighs only 12 kg, taking into account the weight of the container. During transportation and storage, liquid thermal insulation Armor - practically does not break into fractions.

 After applying and curing the Polymer thermal insulator Armor AquaBlock, the floors are ready for finishing coating – which in itself is a huge advantage of Polymer waterproofing, which can be used both during the construction of the foundation and during the necessary repair of floors in the operated premises (We recommend Polymer waterproofing Armor AquaBlock for waterproofing bathrooms, bathrooms, basements and cellars).

For waterproofing walls and/or roofs, polymer waterproofing is the best fit. They can be used both to create a strong insulating layer over a large area, and for sealing joints, seams, cracks and pasting surfaces with tiles, panels and other decorative materials.

For waterproofing walls indoors, it is practical and profitable to use Polymer

waterproofing Armor AquaBlock, which is characterized by strength and

durability, excellent waterproofing characteristics, plasticity, adhesion.

Advantages

1. Distilled water is used as a solvent in the Polymer waterproofing Armor AquaBlock, so it does not have a sharp smell and is harmless in operation (which should be taken into account when choosing materials for repair, especially if elderly family members, children, allergies may be nearby).
2. The surface of the AquaBlock armor has no seams, therefore, it reliably protects against leaks;
3. The elasticity reaches 220%, which indicates high strength of the coating;
4. The waterproofing agent can be applied to any surface, thanks to high adhesion;
5. Easy installation. Applying a waterproofing agent is painting work, which means saving on labor costs;
6. Armor AquaBlock is not affected by sunlight, humidity, temperature difference;
7. High speed of work;
8. AquaBlock armor is easily applied with a brush, roller, spatula and spray guns.
9. After applying the Armor, the AquaBlock turns into a strong and durable coating that is not exposed to atmospheric, mechanical influences. It is both durable and elastic material that does not lose its characteristics during operation.